Sor 1520 OEM Flow Switch Uživatelský manuál Strana 1
Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Sor 1520 OEM Flow Switch. SOR 1520 OEM Flow Switch User Manual Uživatelská příručka
- Strana / 8
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Form 454 (11.13) ©SOR Inc.
1/8
1520 Top Mounted
Flow Switch
General Instructions
Registered Quality System to ISO 9001
The SOR
®
1520 Flow Switch must be mounted in a vertical position (horizontal
pipe run). Electric switching is caused by the liquid flow moving the vane and
magnet into the field of a hermetically sealed reed switch capsule. Flow
switching takes place at approximately 1 ft./sec. velocity.
Two separate cavities make up the body — one for the magnetic/vane arm,
one for the switch.
Before Installing the Level Switch
Inspect the unit for any shipment damage.
Check for mechanical clearance of the vane. The vane must
move freely without binding throughout its stroke.
Use an acceptable thread compound when installing unit to
ensure a leak-free fit and to avoid thread galling.
When installed, the direction of flow should match the direction
of the arrow on the unit.
Design and
specifications are
subject to change
without notice.
For latest revision, go to
sorinc.com
Table of Contents
Installation ....................................... 2
SIL Installation Requirements ................2
Process Connection ............................2
Electrical Connection ...........................3
Special Conditions for Safe Use ..............3
Dimensions ......................................4
ATEX and IECEx Marking Details .............6
Delaration of Conformity ......................7
Troubleshooting .................................8
Replacement Parts .............................8
NOTE: If you suspect that a product is defective, contact the factory or the SOR Representative
in your area for a return authorization number (RMA). This product should only be installed by
trained and competent personnel.
m
,
Shrnutí obsahu
Strany 1 - Flow Switch
Form 454 (11.13) ©SOR Inc. 1/8 1520 Top Mounted Flow SwitchGeneral InstructionsRegistered Quality System to ISO 9001The SOR® 1520 Flow Switch must be
Strany 2 - Installation
2/8Form 454 (11.13) ©SOR Inc. Integrally mounted controls should be mounted with the vessel flange or nozzle within 3° of the vertical or horizontal c
Strany 3 - Electrical Connection
Form 454 (11.13) ©SOR Inc. 3/8Do not exceed catalog stated electrical ratings. Improper current input to switch will cause permanent damage to contact
Strany 4 - Dimensions
4/8Form 454 (11.13) ©SOR Inc. DimensionsLinear = mm/inchesDrawing 0390011
Strany 5 - Drawing 0390762
Form 454 (11.13) ©SOR Inc. 5/8Linear = mm/inchesDrawing 0390762With CK Accessory – ATEX and IECEx dual approved:177.87.0014.30.5655.62.1922.20.87WRENC
Strany 6 - Drawing 0720554
6/8Form 454 (11.13) ©SOR Inc. ATEX and IECEx Marking DetailsFor ATEX and IECEx Certi ed ModelsStandards Assessed To ATEX Certification: EN 60079-0:
Strany 7 - of Conformity
Form 454 (11.13) ©SOR Inc. 7/8Declaration of ConformityFor ATEX/IECExCerti ed Models EC Declaration of Conformity 14685 West 105th Stre
Strany 8 - Troubleshooting
8/8Form 454 (11.13) ©SOR Inc. 14685 West 105th Street, Lenexa, KS 66215 913-888-2630 800-676-6794 USA Fax 913-888-0767Registered Quality S
Související produkty a manuály pro Senzory Sor 1520 OEM Flow Switch
(4 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce