Sor Single Point RF Level Switch Uživatelský manuál stáhnout pdf

Form 759 (03.13) SOR Inc.

1/16



Remove the housing cover.



Place the instrument on an insulated surface or support

so the sensor does not touch a conductive surface.



Apply 12 to 28VDC, and observe the LED. (See on page 2)

NOTE: When the LED is on, it indicates the output is in the normal state 16-20mA.



Turn the sensitivity adjustment clockwise (up to 25 turns) to increase sensitivity until

the LED goes out.

NOTE: Do not turn the sensitivity adjustment past 25 turns! Damage to the unit could result.



Turn the sensitivity adjustment counterclockwise to decrease sensitivity until the

LED illuminates.

Pre-Installation I/O Test and Calibration

651 K9 RF Admittance

Two Wire Point Level Control

General Instructions

Registered Quality System to ISO 9001

Design and

specifications are

subject to change

without notice.

For latest revision, go to

www.sorinc.com

Table of Contents

Pre-Installation I/O and Calibration ....... 1-2

Installation ....................................... 3

Electrical Connections .........................4

Post-Installation Calibration ..................4

SOR RF Probe Grounding Screen ............5

Control Drawings ............................ 6-9

Instructions for EMC .......................... 10

Spare Parts .................................... 10

Information for IEC-Listed Product ......... 10

Maintenance and Troubleshooting ......... 11

Dimensions ................................ 12-13

ATEX and IECEx Marking Details ........... 14

Declaration of Conformity ................... 15

These instructions provide specific information for installation,

electrical connection, calibration and troubleshooting for the

651 K9 RF Admittance Two-Wire Point Level Control.

NOTE: If you suspect that a product is defective, contact the factory

or the SOR

Representative in your area for a return authorization

number.

This product should only be installed by trained and

competent personnel.

1 2 3 4 5 6 ... 15 16

Shrnutí obsahu

Strany 1 - Two Wire Point Level Control

Form 759 (03.13) SOR Inc. 1/16 Remove the housing cover. Place the instrument on an insulated surface or support so the sensor does not touch a co

Strany 2

10/16Form 759 (03.13) SOR Inc. Instructions for EMC651K9When subjected to an RF Interference, the 651K9 will maintain the +1% accuracy in all frequenc

Strany 3 - Installation

Form 759 (03.13) SOR Inc. 11/16Sympton/ProblemPossible Cause Corrective ActionLED stays illuminated, even at maximum sensitivity setting (full clockwi

Strany 4 - Post-Installation Calibration

12/16Form 759 (03.13) SOR Inc. Process ConnectionDim B Dim CCable ProbeAll Other ProbesCable ProbeAll Other Probes3/4” NPT(M)87.83.4694.13.71256.010.0

Strany 5 - SOR RF Probe Grounding Scheme

Form 759 (03.13) SOR Inc. 13/16Dimensions - K Housing Con guration (Explosion Proof Integral)Dual Rigid Probe DetailLinear = mm/inchesDrawing 0390654

Strany 6 - Control Drawing

14/16Form 759 (03.13) SOR Inc. Sample NameplatesLocation of Product Model IdentificationLocation of Serial Number (First Two NumbersIndicate Year of

Strany 7

Strany 8

16/16Form 759 (03.13) SOR Inc. 14685 West 105th Street, Lenexa, KS 66215  913-888-2630  800-676-6794 USA  Fax 913-888-0767Registered Quality

Strany 9

2/16Form 759 (03.13) SOR Inc.  Turn the sensitivity adjustment slowly clockwise until LED goes off, then counterclockwise until LED goes on to chec

Strany 10 - Spare Parts

Form 759 (03.13) SOR Inc. 3/16InstallationOutput SignalFailsafe Hi LoAbsence of Process 16-20mA 4-8mAPresence of Process 4-8mA 16-20mAStandard con gu

Strany 11 - Troubleshooting

4/16Form 759 (03.13) SOR Inc. Electrical ConnectionsWhen the process is adhesive, i.e. it tends to coat the sensor, it may be desirable to mount it on

Strany 12 - Drawing 0390654

Form 759 (03.13) SOR Inc. 5/16SOR RF Probe Grounding SchemeCritical Grounding Path = CircuitBoardLineNeutralGroundElectronics HousingPower Supply

Strany 13 - Dual Cable Probe Detail

6/16Form 759 (03.13) SOR Inc. Control DrawingDrawing 9093008

Strany 14 - Sample Nameplates

Form 759 (03.13) SOR Inc. 7/16Control DrawingDrawing 9093010

Strany 15 - of Conformity

8/16Form 759 (03.13) SOR Inc. Control DrawingDrawing 9093011

Strany 16 - Printed in USA www.sorinc.com

Form 759 (03.13) SOR Inc. 9/16Control DrawingDrawing 9093009