Sor Pivot Seal Weatherproof Pressure Switch Uživatelský manuál stáhnout pdf

Form 496 (01.13) ©SOR Inc.

1/8

Pressure Switches

for Process Applications

General Instructions

Registered Quality System to ISO 9001

Table of Contents

Electrical Connection ...........................1

Installation ....................................... 2

SIL Installation ..................................3

Process Connection ............................3

Calibration .......................................3

ATEX Marking Information .....................4

Declaration of Conformity .....................5

Electrical Connection

Storing excess wire or making wire lead splices inside the pressure switch housing will

interfere with pressure switch operation.

Design and

specifications are subject

to change without notice.

For latest revision, go to

www.sorinc.com

These instructions provide information for electrical

connection, installation, process connection, and

calibration. If the switch is a pivot seal sensor type

(piston 2 or 3), it is recommended for high-pressure

fluid power applications where high-shock pressure

and high-cycle rates are expected. Pivot seal sensors

are designed specifically for those applications.

NOTE: If you suspect that a product is defective, contact the

factory or the SOR

Representative in your area for a return

authorization number (RMA). This product should only be

installed by trained and competent personnel.

Electrical Power must be disconnected from explosion-proof models before

the cover is removed. Failure to do so could result in severe personal injury

or substantial plant damage.

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - Pressure Switches

Form 496 (01.13) ©SOR Inc. 1/8Pressure Switches for Process ApplicationsGeneral InstructionsRegistered Quality System to ISO 9001Table of ContentsElec

Strany 2 - Installation

2/8Form 496 (01.13) ©SOR Inc. Wire Lead Color CodeSPDTDPDT (2-SPDT)Vacuum SwitchInstallationBlue (C)Black (NO)Red (NC)Green (GND)PressureBlue (C)Black

Strany 3 - Calibration

Form 496 (01.13) ©SOR Inc. 3/8Process ConnectionSecurely connect process line to pressure port using two wrenches: one to hold flats on pressure port,

Strany 4 - ATEX Marking Information

4/8Form 496 (01.13) ©SOR Inc. ATEX Marking InformationSample NameplateDrawing 072004xManufacturer’sRegistered TrademarkATEX Listing InformationProduct

Strany 5 - of Conformity

Form 496 (01.13) ©SOR Inc. 5/8Declaration of ConformityFor ATEX Certi ed Models R Series Pressure SwitchesSOR Inc.14685 West 105th StreetLenexa, Ka

Strany 7

Strany 8 - Printed in USA www.sorinc.com

8/8Form 496 (01.13) ©SOR Inc. 14685 West 105th Street, Lenexa, KS 66215  913-888-2630  800-676-6794 USA  Fax 913-888-0767Registered Quality S

Další dokumenty pro Senzory Sor Pivot Seal Weatherproof Pressure Switch

Zobrazit dokument Sor Pivot Seal Weatherproof Pressure Switch Uživatelský manuál

Sor Pivot Seal Weatherproof Pressure Switch Uživatelský manuál (4 stránky)

Komentáře k této Příručce

Žádné komentáře

Sor Pivot Seal Weatherproof Pressure Switch Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Senzory Sor Pivot Seal Weatherproof Pressure Switch. SOR Pivot Seal Weatherproof Pressure Switch User Manual Uživatelská příručka

Shrnutí obsahu

Další dokumenty pro Senzory Sor Pivot Seal Weatherproof Pressure Switch

Komentáře k této Příručce

Související produkty a manuály pro Senzory Sor Pivot Seal Weatherproof Pressure Switch